China best Domestic End Brackets or Supports for Ball Screw (Sfu1604 with Free Design Custom

Product Description

Product Description

Ball screw brackets
Description:
Ball screw brackets is supporting the connection screw and motor bearing brackets, brackets general points: fixed side (K add after such as BK12) and support unit is installed (F if BF12) are useful for the adjustment of the preloading JIS5 level of angular contact ball bearings.
Ball screw brackets, containing for subminiature ball screw developed by contact Angle 45 ° subminiature angular contact ball bearings, can obtain high rigidity, high precision of steady turning performance.Support the lateral support unit use deep groove ball bearings.Support unit such as EK, BK type internal bearing load of the right amount of lithium soap grease, with a special seal gasket to seal, can be installed directly, can use for a long time.

Specifications and feature

1) It is matched with the ball screw shaft , the whole together works well .(ball screw assemble including –Ball screw shaft, Ball screw nut, Nut housing, End supports and coupling)
2)Rolled and ground
3)Super high presicion
4)Low noise
5)Low backlash
6)In large stock
7)Prompt delivery
8) the material is S45C carbon steel
9) No MOQ demand

We can supply a range size of the end support unit bearings suitable for ball screw and lead screw. Available in both flanged and pillow block versions that cater for shaft diameter from 4mm up to 40mm.

ball screw end support unit:

BK type: thrust pillow block fixed
 
BK10, BK12, BK15, BK17, BK20, BK25, BK30, BK35, BK40, BK50
BF type: radial simple support
 
BF10, BF12, BF15, BF17, BF20, BF25, BF30, BF35, BF40, BF50
EK type: fixed side
 
EK06, EK08, EK10, EK12, EK15, EK20, EK25
EF type: floated side
 
EF06, EF08, EF10, EF12, EF15, EF20, EF25
FK type: flange mount thrust bearing
 
FK06, FK08, FK10, FK12, FK15, FK17, FK20, FK25, FK30, FK40
FF type: flange mount simple support
 
FF06, FF08, FF10, FF12, FF15, FF17, FF20, FF25, FF30, FF40

 

Ball screw nut housing series:

Ball screw size Nut housing size and material
SFU1204/SFS1205/SFS1210 DSG12H / iron steel / aluminium alloy
SFU1605/1605/SFS1605/SFS1610/SFS1616/SFS1620 DSG16H / iron steel / aluminium alloy
SFU2004/2005/2571/SFS2005/SFS2571/SFS2571 DSG20H /iron steel / aluminium alloy
SFU2504/2505/2571/SFS2505/SFS2510/SFS2525 DSG25H /iron steel / aluminium alloy
SFU3205/3210/SFS3205/SFS3210/SFS3220/SFS3232 DSG32H /iron steel / aluminium alloy
SFU4005/4571/SFS4005/SFS4571/SFS4571/SFS4040 DSG40H / iron steel / aluminium alloy

Product Parameters

Ball screw nut housing size:

Detailed Photos

There are many parts what can be matched into the ball screw, Please
choose what you need:

Related products

There are many kinds of products we can offer, If you are interested in them,
please click the picture and see the details.

Our Advantages

Our Advantages: High precision good machines, Professional QC department and test rooms,

Our service

Our principle:

Quality first, credibility is the key, the price followed

Packaging & Shipping

Packaging & Delivery
PP bag for each linear shaft, Standard exported carton outside for small order shipping by international express,such as DHL, TNT, UPS,Wooden box outside for big quantity or very
long linear shaft by sea, by air

Packaging Details: 1. Individial plastic bag, paper box ,secure carton 2. As clients’ requirement.
Delivery Detail: Within 3–7 Days Against the Down Payment

Company Profile

12,Production flow

ERSK Company Image

Our service and after-sale service

1. We have a group of professional engineers we can provide drawings according to customer’s requirements.

2. We have more than 20 machines for offering professional ball screws end machining service.

3. We can rebuild, refurbish, and make emergency repairs to ball screws and linear guideways.

4. We can disassemble, clean, polish ball screws and linear guideways.

5. Two years free maintenance to ball screws and 1 years free maintenance to linear guideways.

High Quality With Reasonable Price

Why Choose Us? —-ERSK—–

1)ERSK professional manufacturer

We have the professional production team, high precision production equipments ,focused on precision transmission parts for 10years and have our own brand name CZPT .

2) Quality control

1. We have QC department to control quality for each step.

2. We also have Automatic product equipments(German Chiron FZ15W ,DMG XIHU (WEST LAKE) DIS. MAX3000 Machining Centers ) which can cantrol the precision itself

3. ISO9001:2008

3)Competitive Price

ERSK is a manufactory which can export directly to customer, so there is no intermediary cost involved. We provide our foreign customer lower price than the domestic market. Since we can get tax refund from the government.

4)Quickly Delivery

We are big manufacturer ,have large amount of stock, we can delivery customer’s order just-in-time for small order, 7-15 days for big order.

5) Best After-Sale Service

ERSK supply the after-sale service and technical assistance as per customer’s requirement and needs. Customers are always given quick support.

Get more detailed information !!!
Inquiry with us, Now!!!

We will reply within 24 Hours!!!

Thank you for visiting!!!

 

 

Screw Sizes and Their Uses

Screws have different sizes and features. This article will discuss screw sizes and their uses. There are 2 main types: right-handed and left-handed screw shafts. Each screw features a point that drills into the object. Flat tipped screws, on the other hand, need a pre-drilled hole. These screw sizes are determined by the major and minor diameters. To determine which size of screw you need, measure the diameter of the hole and the screw bolt’s thread depth.

The major diameter of a screw shaft

The major diameter of a screw shaft is the distance from the outer edge of the thread on 1 side to the tip of the other. The minor diameter is the inner smooth part of the screw shaft. The major diameter of a screw is typically between 2 and 16 inches. A screw with a pointy tip has a smaller major diameter than 1 without. In addition, a screw with a larger major diameter will have a wider head and drive.
The thread of a screw is usually characterized by its pitch and angle of engagement. The pitch is the angle formed by the helix of a thread, while the crest forms the surface of the thread corresponding to the major diameter of the screw. The pitch angle is the angle between the gear axis and the pitch surface. Screws without self-locking threads have multiple starts, or helical threads.
The pitch is a crucial component of a screw’s threading system. Pitch is the distance from a given thread point to the corresponding point of the next thread on the same shaft. The pitch line is 1 element of pitch diameter. The pitch line, or lead, is a crucial dimension for the thread of a screw, as it controls the amount of thread that will advance during a single turn.
screwshaft

The pitch diameter of a screw shaft

When choosing the appropriate screw, it is important to know its pitch diameter and pitch line. The pitch line designates the distance between adjacent thread sides. The pitch diameter is also known as the mean area of the screw shaft. Both of these dimensions are important when choosing the correct screw. A screw with a pitch of 1/8 will have a mechanical advantage of 6.3. For more information, consult an application engineer at Roton.
The pitch diameter of a screw shaft is measured as the distance between the crest and the root of the thread. Threads that are too long or too short will not fit together in an assembly. To measure pitch, use a measuring tool with a metric scale. If the pitch is too small, it will cause the screw to loosen or get stuck. Increasing the pitch will prevent this problem. As a result, screw diameter is critical.
The pitch diameter of a screw shaft is measured from the crest of 1 thread to the corresponding point on the next thread. Measurement is made from 1 thread to another, which is then measured using the pitch. Alternatively, the pitch diameter can be approximated by averaging the major and minor diameters. In most cases, the pitch diameter of a screw shaft is equal to the difference between the two.

The thread depth of a screw shaft

Often referred to as the major diameter, the thread depth is the outermost diameter of the screw. To measure the thread depth of a screw, use a steel rule, micrometer, or caliper. In general, the first number in the thread designation indicates the major diameter of the thread. If a section of the screw is worn, the thread depth will be smaller, and vice versa. Therefore, it is good practice to measure the section of the screw that receives the least amount of use.
In screw manufacturing, the thread depth is measured from the crest of the screw to the root. The pitch diameter is halfway between the major and minor diameters. The lead diameter represents the amount of linear distance traveled in 1 revolution. As the lead increases, the load capacity decreases. This measurement is primarily used in the construction of screws. However, it should not be used for precision machines. The thread depth of a screw shaft is essential for achieving accurate screw installation.
To measure the thread depth of a screw shaft, the manufacturer must first determine how much material the thread is exposed to. If the thread is exposed to side loads, it can cause the nut to wedge. Because the nut will be side loaded, its thread flanks will contact the nut. The less clearance between the nut and the screw, the lower the clearance between the nut and the screw. However, if the thread is centralized, there is no risk of the nut wedgeing.
screwshaft

The lead of a screw shaft

Pitch and lead are 2 measurements of a screw’s linear distance per turn. They’re often used interchangeably, but their definitions are not the same. The difference between them lies in the axial distance between adjacent threads. For single-start screws, the pitch is equal to the lead, while the lead of a multi-start screw is greater than the pitch. This difference is often referred to as backlash.
There are 2 ways to calculate the pitch and lead of a screw. For single-start screws, the lead and pitch are equal. Multiple-start screws, on the other hand, have multiple starts. The pitch of a multiple-start screw is the same as its lead, but with 2 or more threads running the length of the screw shaft. A square-thread screw is a better choice in applications requiring high load-bearing capacity and minimal friction losses.
The PV curve defines the safe operating limits of lead screw assemblies. It describes the inverse relationship between contact surface pressure and sliding velocity. As the load increases, the lead screw assembly must slow down in order to prevent irreversible damage from frictional heat. Furthermore, a lead screw assembly with a polymer nut must reduce rpm as the load increases. The more speed, the lower the load capacity. But, the PV factor must be below the maximum allowed value of the material used to make the screw shaft.

The thread angle of a screw shaft

The angle between the axes of a thread and the helix of a thread is called the thread angle. A unified thread has a 60-degree angle in all directions. Screws can have either a tapped hole or a captive screw. The screw pitch is measured in millimeters (mm) and is usually equal to the screw major diameter. In most cases, the thread angle will be equal to 60-degrees.
Screws with different angles have various degrees of thread. Originally, this was a problem because of the inconsistency in the threading. However, Sellers’s thread was easier to manufacture and was soon adopted as a standard throughout the United States. The United States government began to adopt this thread standard in the mid-1800s, and several influential corporations in the railroad industry endorsed it. The resulting standard is called the United States Standard thread, and it became part of the ASA’s Vol. 1 publication.
There are 2 types of screw threads: coarse and fine. The latter is easier to tighten and achieves tension at lower torques. On the other hand, the coarse thread is deeper than the fine one, making it easier to apply torque to the screw. The thread angle of a screw shaft will vary from bolt to bolt, but they will both fit in the same screw. This makes it easier to select the correct screw.
screwshaft

The tapped hole (or nut) into which the screw fits

A screw can be re-threaded without having to replace it altogether. The process is different than that of a standard bolt, because it requires threading and tapping. The size of a screw is typically specified by its major and minor diameters, which is the inside distance between threads. The thread pitch, which is the distance between each thread, is also specified. Thread pitch is often expressed in threads per inch.
Screws and bolts have different thread pitches. A coarse thread has fewer threads per inch and a longer distance between threads. It is therefore larger in diameter and longer than the material it is screwed into. A coarse thread is often designated with an “A” or “B” letter. The latter is generally used in smaller-scale metalworking applications. The class of threading is called a “threaded hole” and is designated by a letter.
A tapped hole is often a complication. There is a wide range of variations between the sizes of threaded holes and nut threads, so the tapped hole is a critical dimension in many applications. However, even if you choose a threaded screw that meets the requisite tolerance, there may be a mismatch in the thread pitch. This can prevent the screw from freely rotating.

China best Domestic End Brackets or Supports for Ball Screw (Sfu1604   with Free Design CustomChina best Domestic End Brackets or Supports for Ball Screw (Sfu1604   with Free Design Custom